How to Fit CoyoteSpurs on Your Dog's Collar or Vest

By CoyoteVest | Published: 2026-11-03

Category: Ohjeet

CoyoteSpurs hang from your dog's collar or vest without touching the legs. Follow these steps to position them for protection, comfort, and freedom of movement.

Quick answer

Fit CoyoteSpurs by suspending them from your dog's collar or vest so they hang near the legs without touching them. Check that the spurs stay clear of the ground and your dog's stride, then tighten all attachment points before every walk.

Why CoyoteSpurs hang free instead of strapping to the legs

CoyoteSpurs are designed to protect your dog's legs from surprise attacks without restricting natural movement. The spurs are suspended in the air near the legs rather than attached to them, so your dog can run, jump, and turn freely. That floating design is what makes correct positioning essential: if the spurs sit too low or too far forward, they can catch on obstacles or interfere with your dog's stride. If they sit too high, they may not cover the vulnerable leg area. The goal is a balanced hang that stays close to the legs but never touches them during normal activity.

Collar vs. vest mounting: which is more stable for your dog

A standard CoyoteVest already covers the torso, but the legs can remain exposed if your dog tries to run during an attack. Mounting CoyoteSpurs on the vest keeps the spurs aligned with the body and reduces swinging compared with a collar-only setup. A collar mount is quicker to put on and works well for dogs that already wear a collar comfortably, but it can shift more on narrow-chested or long-necked dogs. If your dog wears both, use the vest as the primary anchor and the collar only as a secondary point if the spur design allows it. Whichever you choose, the mounting point must be snug enough that the spurs cannot rotate out of position.

When to recheck the fit

Fit can change with your dog's coat, weight, and gear layering. A thick winter coat can push the spurs outward, while a summer clip can leave the same setup loose. Recheck the hang after grooming, after switching between a collar and vest, and whenever you notice your dog pawing at the spurs or altering its gait. If the spurs touch the ground when your dog stands or walks, they are too low and need to be raised before the next outing.

Step-by-step CoyoteSpurs installation

Choose the mounting point: Decide whether the spurs will hang from your dog's collar or from the CoyoteVest. Pick the option that sits closest to the leg area without pressing on the neck or shoulders. For most dogs, the vest gives a more stable anchor because it distributes weight across the torso. Common mistake: mounting too far back on the vest, which leaves the front legs uncovered.
Attach the spurs loosely enough to hang free: Fasten each spur to the collar or vest using the supplied attachment points. The spur should dangle freely and never touch your dog's leg when standing still. You should be able to slide a finger between the spur and the leg. Checkpoint: lift each spur and let it drop; it should swing without catching on fur or gear.
Set the height so the spurs clear the ground: With your dog standing on a level surface, adjust the attachment so the lowest point of each spur stays at least a few inches above the ground. If the spur touches the floor, raise it by moving the attachment higher on the collar or vest. Common mistake: fitting while your dog is lying down, which makes the spurs look higher than they are when standing.
Test the range of motion: Walk your dog on a leash and watch for any change in stride. The spurs should stay near the legs but not swing into them during turns or stops. If your dog avoids one side or bunny-hops, the spur on that side is likely too low or too close. Checkpoint: film a short video from the side to see the hang in motion.
Secure loose ends and recheck tension: Tighten any straps or clips so the spurs cannot rotate around the collar or slide along the vest. The mounting point should be firm but not tight enough to compress your dog's coat or skin. Recheck after five minutes of walking, since gear can settle. Common mistake: over-tightening a collar-mounted spur, which can twist the collar and shift the spur sideways.
Do a final clearance check before every walk: With your dog standing, confirm that no spur touches a leg, the ground, or another piece of gear. Make sure the spurs hang symmetrically on both sides. If your dog wears a coat or harness over the vest, refit the spurs after layering. Checkpoint: if anything touches, adjust before you leave, not during the walk.

Product facts

CoyoteSpurs: CoyoteSpurs are suspended in the air near the legs and are not actually attached to your dog's legs. This means correct positioning depends on the mounting point, not on leg straps, so you need to check clearance and hang before each use.
CoyoteSpurs